Of course, you can buy a brazier today in any specialized store. But the cost of some models is quite high, so not everyone can afford such a luxury. In addition, sometimes ready-made designs are completely unsuitable for cooking products due to being too large or small.
But you should not despair, because there is a way out. A brazier made of automobile disks remains quite convenient and practical. In fact, everything is done very simply, it is only important to stick to some plan.
Material selection criteria
If you have finally decided to create a brazier from car rims, then it is best to borrow material from the Zhiguli. At the same time, make sure that the material is solid steel, but not aluminum alloy. Today it is not difficult to find such products. It is enough to go to a tire service, where you can select suitable wheels for free or at a small cost.
If this option is unacceptable for you, then buy the discs in the online store. Products that have already been used for their intended purpose are much lower than new ones. The remaining parts - bolts, pipes, wires and nuts can be bought at every hardware store.
On the video - how a brazier is made from car disks:
Versions
The peculiarity of such a homemade brazier is that it can also be made in various versions.
To make a brazier from car rims, you need to look at the following models:
- Regular grill. The wheel is the container in which the coals will be located. Place skewers or a grill on it and wait for your meat to fry. But what a do-it-yourself vertical brazier looks like can be understood by looking at the contents of this
Ordinary brazier from car disks
- Double construction. For this brazier, you need to use 2 wheels. Due to this, the brazier becomes higher. From above, you can even install a cauldron. Heating from all sides allows you to cook delicious dishes in it. But this is what a cast-iron grill for a barbecue looks like, and how to use it, this will help to understand
Double barbecue
- closed oven. Thanks to this design, it is possible to smoke products. The fact is that smoke is concentrated inside the chamber, and then it is removed in small quantities through special openings. But how a collapsible brazier with a roof will look like, and how to use it, information will help to understand
Closed car rim oven
- Complex Models. They combine 4 functions of those designs that were presented earlier. Additionally, they can be equipped with other elements, for example, it can be a chimney. But what are the projects of a gazebo with a barbecue grill and a stove, you can understand by watching the video in this
Integrated brazier
In addition, a homemade brazier from car wheels can be supplemented with legs or be made without them. The stand is necessary only for single products, but double and triple models do not need it, since the lower disk takes over its functions. Despite this, there are certain limitations regarding the application of the structure, since moist ground can prevent the formation of heat, and hot steel is not allowed to come into contact with the wooden flooring on the terrace.
But what the forester thermo brazier looks like can be seen in the photo in this article:
But what are the dimensions of the correct brazier made of metal, and how it looks, this will help to understand
Sequence of work
To make a brazier from car rims, it is necessary to strictly follow a number of rules, thanks to which you can create a durable structure.
Foundation preparation
After you have picked up all the necessary materials, you need to take one of the disks and cut out the partition.
For these purposes, you can use a gas cutter or use a grinder to make notches, which can later be broken out with a hammer.
Now connect the two disks around the perimeter by welding. The result of the actions taken will be a metal container in which one partition remains, and it will serve as the bottom.
Door manufacturing
This stage is considered one of the most difficult and responsible. Thanks to the presence of the door, it will be possible to cook dishes in a cauldron without disturbing the temperature. Another door allows you to throw firewood, and for this you do not need to remove the dish from the grill.
In order for all work to be done neatly, it is necessary to mark a rectangle, and in its center there will be a weld.
The bottom side of the door will be a couple of centimeters higher than the bottom. Cut out a rectangle according to the markings. Process its edges so that there are no sharp edges and burrs. Now you can attach the bolt heads to one of the vertical sides.
On the video - how to make a brazier from car rims:
Drill a hole that will be focused close to the opposite edge by 2 cm. Install the third bolt into it. At the same time, make sure that it comes out 3-5 cm from the outside. This will be the door handle. Screw nuts onto the welded bolts. Then weld them to the body.
legs
Now you need to start making the legs and eliminate the holes in the bottom. The legs are of such a height that there is no discomfort when frying meat. Everyone here has their own dimensions. But the optimal height is 60-80 cm.
When the length of the legs is calculated, then you need to cut 3 identical pieces of the profile pipe. Weld them at an equal distance to the bottom. In this case, the existing factory holes must be taken into account.
The angle of inclination will be the same. Everything is worth doing 3 legs, then the design will be as stable as possible. Even on an uneven surface, the brazier will stand confidently and not sway.
Handle making
To make it convenient to use a homemade barbecue, it is necessary to provide handles. To do this, rotate the case so that the door is in front of you. Mentally draw a line according to which the entire brazier will be divided into two parts. Now mark with a marker. This line will become the middle of the handles.
From the intended line, lower the perpendicular line. On the sides of the case wall, now step back from the edge of the upper disk 5 cm on both sides and set new marks. According to them, weld 4 nuts. Pass handles bent from 8 mm wire into them. The bottom of the brazier is not recommended to be brewed. It is better to cover it with a metal mesh. This will promote good traction.
Additional trivia
You can paint the brazier with heat-resistant paint and it is better to choose a dark color. Black in this case will look very noble.
Brazier from car tires is a great opportunity to get an efficient and at the same time inexpensive brazier. You can safely install it at home, in the country and delight your loved ones with delicious dishes. The service life of such a design is quite high, if the material was selected with high quality, and all the work was done correctly.